Dalsa HM1400 XDR Manual de usuario Pagina 20
- Pagina / 157
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
18 • Installing the Genie Camera Genie HM Series-GigE Vision Camera
Installation Overview & Preparations
The Genie camera installation generally follows the sequence described below. Detailed installation instructions
follow this overview. This section also provides important information to prevent operational faults due to ESD
(electrostatic discharge) in Genie installations.
Network and Computer Overview
• Genie needs to connect to a computer with a GigE network adapter, either built in on the computer
motherboard or installed as a third party PCI adapter.
• Laptop computers with built in GigE network adapters may still not be able to stream full frame rates from
Genie, especially when on battery power. Thorough testing is required with any laptop computer to determine
the maximum frame rate possible (see "
Older Laptop Computer Networking Issues" on page 144).
• Genie also can connect through a Gigabit Ethernet switch. When using VLAN groups, the Genie and
controlling computer must be in the same group (see "
Using Genie with a VLAN Ethernet Switch" on page 93).
• If Genie is to be used in a Sapera development environment, Sapera LT needs to be installed, either before or
after the Genie software package. If Genie will be used in a GigE Vision Compliant environment, Sapera or
Sapera runtime is not required and you need to follow the installation instructions of the third party GigE
Vision compliant package.
• Install the Genie Framework software package if not using a third party GigE Vision compliant package.
Also install Sapera Run-time with CamExpert to control the Genie.
• The Windows Firewall exceptions feature is automatically configured to allow the Sapera GigE Server to pass
through the firewall.
• Computers with VPN software (virtual private network) may need to have the VPN driver disabled in the NIC
properties. This would be required only on the NIC used with the Genie. Testing by the user is required.
- HM Series 1
- *CA-GENM-HUM00* 2
- Contents 3
- Genie HM Series Overview 9
- Genie Application Advantages 10
- Product Part Numbers 11
- Supported Industry Standards 13
- Genie HM Series Responsivity 15
- Test conditions 16
- Sapera LT 17
- Framework 17
- Installing the Genie Camera 19
- Installation Overview 21
- Procedure 23
- GigE Server Verification 23
- Connect the Genie Camera 24
- Status LED Codes 25
- GigE Server Status 26
- Jumbo Frames 27
- Interrupt Moderation Rate 28
- Jumbo Frames Optimization 29
- Updating Genie Firmware 32
- Quick Test with CamExpert 33
- Creating the Response File 35
- Operational Reference 37
- Read Only Parameters 38
- User Set Parameters 38
- Power-up Parameter List 39
- Applications 40
- Sensor Controls 41
- Scan Start Offset 44
- Scan Line Count 44
- Partial Image Scan 44
- Horizontal Crop 46
- Binning 49
- Trigger Modes 50
- Exposure Controls 51
- Synchronization Timing 55
- Reset Mode 56
- I/O Controls Dialog 57
- General Inputs 58
- Strobe and General Outputs 60
- Genie Processing Features 65
- Programmed as 66
- Invert Function 66
- Verify a Dark Acquisition 68
- Indicates one or more 68
- “hot” pixels 68
- Average dark pixel value 68
- Verify a Bright Acquisition 68
- Horizontal Flip 72
- Mount Genie 72
- Upside Down 72
- The Genie test patterns are: 73
- Sapera Callbacks 74
- Parameter Description 77
- Feature Type STRING 80
- Feature Type ENUM 80
- (type INT32) 82
- Feature Type BOOL 83
- Device 84
- User Defined Buffers 84
- Sensor 84
- Sensor Exposure 85
- Acquisition ROI 85
- Binning Control 85
- LUT Control 85
- Flat Field Control 85
- Trigger Control 86
- I/O Control 86
- Time Stamp Control 86
- Network Parameters 87
- User Options 87
- Trigger Enable - TRUE 89
- Trigger Enable - FALSE 89
- Output Selector 90
- Vertical Binning 90
- Horizontal Binning 91
- Pixel Format 91
- Network Configuration Mode 92
- Miscellaneous Dependencies 92
- Network Overview & Tools 95
- Link-Local Address (LLA) 96
- Persistent IP 98
- Network Configuration Tool 99
- Genie IP Configuration 100
- General System Information 100
- System Configuration 101
- System DHCP Configuration 102
- NIC Information 102
- Creating a Status Report 104
- Sapera GigE Server Details 105
- Status Window Description 106
- Sapera CamExpert Guide 107
- CamExpert Panes 108
- CamExpert LUT Controls 109
- 10-bit Invert LUT 110
- Technical Specifications 111
- Connectors 116
- External Inputs 117
- TTL External Signal Example 118
- External Outputs 119
- Camera Status LED 120
- Optical Considerations 120
- Lens Selection Overview 122
- Genie HM 1400 Sensor 124
- Sensor Handling Instructions 125
- Cleaning the Sensor Window 126
- Environment 126
- C/CS-Mount NIR and UV Filter 128
- Focal Point with 129
- (see text) 129
- Network Adapters 130
- Laptop Information 130
- Troubleshooting 133
- Multiple Camera Issues 134
- Other IP Issues 134
- Always Important 134
- Getting Timeout Messages 134
- No Timeout messages 134
- Other problems 135
- Firmware Updates 141
- Power supply problems: 142
- Communication problems: 142
- Disabling Windows Firewall 143
- Ethernet Switch Issues 147
- Other Problems or Issues 148
- DALSA Contact Information 149
- Genie Technical Support 150
- Glossary of Terms 151
Relacionado con productos y manuales para Cámaras De Seguridad Dalsa HM1400 XDR
Cámaras De Seguridad Dalsa C1410 Manual de usuario
(131 paginas)
(131 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.147 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales