Dalsa BOA Manual de instalación

teledynedalsa.com/ipd 1 Version 02 BOA Pro Smart Vision System Installation Manual

Version 02 teledynedalsa.com/ipd 10 The BOA vision system offers flexible cabling options to suit a number of application configurations: Cable Conf

Version 02 teledynedalsa.com/ipd 11 Ethernet Only Setup with Lamp 1. Connect the M12-8 male end of the Ethernet cordset (A-BVS-E8S-X) to the M12-8 f

Version 02 teledynedalsa.com/ipd 12 Ethernet and I/O Setup with Lamp 1. Connect the M12-8 male end of the Ethernet cordset (A-BVS-E8S-X) to the M12-

Version 02 teledynedalsa.com/ipd 13 Software Interface The BOA vision system is supplied with the Sherlock Embedded application embedded. This appli

Version 02 teledynedalsa.com/ipd 14 iDiscover Utility Once launched the GUI below will be shown. The left panel shows the MAC addresses of all reach

Version 02 teledynedalsa.com/ipd 15 Software Interface Change the Address Using a Web Browser The BOA static IP address can be changed through the S

Version 02 teledynedalsa.com/ipd 16 The Sherlock Embedded Web Server is a portal through which the BOA Pro vision system can be Monitored when runni

Version 02 teledynedalsa.com/ipd 17 When the application is set up and stored on the camera, the Ethernet connection can be disconnected and the ins

Version 02 teledynedalsa.com/ipd 18 The Sherlock Embedded Client Software is used to program and configure the inspection and peripheral communicati

Version 02 teledynedalsa.com/ipd 19 Specifications This following table lists the specifications of the BOA vision system: General Specifications Sp

Version 02 teledynedalsa.com/ipd 2 Notice BOA Pro Vision System Installation Manual Document Number 405-00031-00 Revision: 02 Copyright © 2012 Teled

Version 02 teledynedalsa.com/ipd 20 Input Specifications The BOA vision system provides two dedicated opto-isolated, polarity independent inputs. On

Version 02 teledynedalsa.com/ipd 21 Output Specifications The BOA vision system provides two dedicated opto-isolated, solid state relay outputs and

Version 02 teledynedalsa.com/ipd 22 Output Control with Sherlock Embedded The Sherlock Embedded application provides programmable options for contro

Version 02 teledynedalsa.com/ipd 23 Panel Link Specifications The PL-100 module offers additional isolation for the BOA camera and simplifies wiring

Version 02 teledynedalsa.com/ipd 24 Panel Link Wiring Illustration 24V GND TRG ICMN IN0 ERTH 24V GND NC OUT0 OCMN OUT1 24V 24V GND TRG+

Version 02 teledynedalsa.com/ipd 25 Serial Port Connection The RS-232 serial port is accessible through the Lamp connector. By default, the serial p

Version 02 teledynedalsa.com/ipd 26 BOA Mechanical Dimensions Front View Back View Side View Bottom View Note: All dimensions in mm

Version 01 teledynedalsa.com/ipd 27 A-BVS-PL-100 Mechanical Dimensions Side View Top View Note: All dimensions in mm

Version 02 teledynedalsa.com/ipd 3 Certifications Declaration of Conformity Manufacturer Teledyne DALSA Corporation 605 McMurray Road Waterloo N2V

Version 02 teledynedalsa.com/ipd 4 Care should always be exercised when handling and operating your BOA Vision System. Even though the system is enc

Version 02 teledynedalsa.com/ipd 5 Table Of Contents Introduction Overview ……………………... 6 Product Support ……………………...

Version 02 teledynedalsa.com/ipd 6 Introduction BOA vision system is the hardware platform. Sherlock Embedded is the powerful and flexible professio

Version 02 teledynedalsa.com/ipd 7 BOA Pro vision systems are shipped with the components listed below. Take a few moments to verify that everything

Version 02 teledynedalsa.com/ipd 8 Installation This section details how to connect the BOA vision system with its associated components and factory

Version 02 teledynedalsa.com/ipd 9 The BOA vision system is compatible with M12 factory cordsets as show below: Cable Pinouts LAN Connector Pinout a