Dalsa Spyder3 Manual de usuario descargar pdf (Pagina 18)

18 Spyder3 GigE Vision SG-14 Monochrome Cameras User’s Manual

03-032-20123-01 Teledyne DALSA

5. Select ―Use the following IP address‖ and set the IP address to any address in this subnet other

than 192.168.5.100, which is used by the camera. In the example below, the address 192.168.5.50 is

used. Alternatively, select ―Obtain an IP address automatically‖ to use a dynamic address.

6. Set subnet to: 255.255.255.0 and click on ―OK.‖

Figure 9. IP Address

7. Click ―OK‖ to save settings

8. Click on ―Configure‖ button and select ―Advanced‖ tab

9. Enable ―Jumbo Frames‖ to greater than 9000 bytes. If your NIC does not support jumbo packets

the image transfer speed will be slower.

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 103 104

Spyder3 SG-14 1
Support 2
Industry Standards 2
Contents 3
The Spyder3 SG-14 Cameras 6
Certifications 10
Responsivity 11
Mechanicals 12
Image Sensor 14
Host System Requirements 15
Network Adapter Requirements 15
5. Operate the Camera 16
Install Network Card 17
Configure Network Card 17
Power Connector 20
Status LED 21
GPIO Isolation 22
GPIO Configuration 22
TTL Inputs and Outputs 23
Power on the camera 24
Connect to the camera 24
Check LED Status 24
Software Interface 24
CamExpert Panes 26
Review a Test Pattern Image 28
Camera Operation 29
User Setting 32
Factory (Default) Settings 32
External trigger 33
Software trigger 33
Valid Data From 34
Diagramed 34
Set the Exposure Mode 35
Exposure Modes in Detail 36
Line Rate 37
Exposure Time 38
Triggers 38
Input / Output Control 39
Image Size 41
Pixel Format 42
Sensitivity Mode 42
Sensor Direction Control 42
Sensor Shift Direction 43
Binning 44
Resetting the Camera 44
Camera Calibration 45
Analog Processing 46
Digital Processing 46
Set Analog Gain 47
Calibrate Camera Gain 47
Calibration Returns: 48
Update Analog Gain Reference 49
Calibration Overview 49
Correction Overview 50
Digital Signal Processing 51
Step 2: FPN Calibration 53
PRNU Calibration Results 54
Setting Digital Offset 54
Subtracting Background 54
Setting Digital System Gain 54
Gate Dark Current Clear 55
Auto Mode (srm 0) 55
Setting the Readout Mode 57
Appendix B: Sensitivity Mode 58
Pixel DetailPixel Detail 59
The GPIO Connector 60
Configure GPIO Signal Levels 61
Internal frame trigger 62
Encoder 66
Outputs 71
Trigger Settings: GURU Mode 73
Pulse Generator 76
Pulse Period (ns) 77
Pulse Frequency (Hz) 77
Pulse Generator Timing 77
Rescaler 78
Counter 80
Input Debouncing 81
Timestamp Counter 82
Clear Mode 83
Clear Input 83
Broadcast 83
Set Value 83
Current Value 83
Delayer 84
The PLC Control Block 85
GPIO Output Labels 87
Signal Routing Block 89
How the Lookup Table Works 93
Appendix D: EMC Declaration 94
Examples: Setting the FVAL 99
Revision History 102

Comentarios a estos manuales

Sin comentarios

Dalsa Spyder3 Manual de usuario Pagina 18

Comentarios a estos manuales

Relacionado con productos y manuales para Cámaras De Seguridad Dalsa Spyder3