Dalsa Spyder3 Manual de usuario Pagina 52
- Pagina / 104
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
52 Spyder3 GigE Vision SG-14 Monochrome Cameras User’s Manual
03-032-20123-01 Teledyne DALSA
GigE Vision Input Controls
Advanced Processing
Parameter
Description
FFC Coefficient Set No.
Selects the pixel set to load, or save. There are 4 user sets available.
Load FFC Coefficient
Loads the Flat Field Correction Coefficients (specified by the Pixel Set
Selector) from the cameras non-volatile memory.
Reset FFC Coefficients
Restores the cameras pixel coefficients to 0 for FPN and a PRNU factor of 1.
This command does not reset saved coefficients.
Save PRNU
Write all current PRNU coefficients to non-volatile memory when Pixel Set
Selector is not Default
Save FPN
Write all current FPN coefficients to non-volatile memory when Pixel Set
Selector is not Default
FPN Calibrate
Perform a Fixed Pattern Noise calibration. Please block all light from entering
the camera(i.e. cover the lens). *** WARNING: This command can take up to
3 seconds. Please adjust the GUI's timeout values
Target to Calibrate PRNU
The target value for the PRNU calibration algorithm
PRNU Calibrate
Calibrate PRNU coefficients. Ideally FPN calibration should be done before
the PRNU calibration. To calibration PRNU, the direction must not be
External. Always set proper target before click this button. *** WARNING:
This command can take up to 15 seconds.
FPN Enable
Enables and disables the fixed pattern noise correction
PRNU Enable
Enables and disables the photo response non-uniformity correction
Calibration Result
Displays the result from the flat field calibration.
Read FFC Calibration
Result
Read FFC Calibrate Result
Region of Interest X
The horizontal start of the region of interest. The region of interest is used
specify which part of the sensor to calibrate.
Region of Interest Width
The width of the region of interest. The region of interest is used specify
which part of the sensor to calibrate
- Spyder3 SG-14 1
- Support 2
- Industry Standards 2
- Contents 3
- The Spyder3 SG-14 Cameras 6
- Certifications 10
- Responsivity 11
- Mechanicals 12
- Image Sensor 14
- Host System Requirements 15
- Network Adapter Requirements 15
- 5. Operate the Camera 16
- Install Network Card 17
- Configure Network Card 17
- Power Connector 20
- Status LED 21
- GPIO Isolation 22
- GPIO Configuration 22
- TTL Inputs and Outputs 23
- Power on the camera 24
- Connect to the camera 24
- Check LED Status 24
- Software Interface 24
- CamExpert Panes 26
- Review a Test Pattern Image 28
- Camera Operation 29
- User Setting 32
- Factory (Default) Settings 32
- External trigger 33
- Software trigger 33
- Valid Data From 34
- Diagramed 34
- Set the Exposure Mode 35
- Exposure Modes in Detail 36
- Line Rate 37
- Exposure Time 38
- Triggers 38
- Input / Output Control 39
- Image Size 41
- Pixel Format 42
- Sensitivity Mode 42
- Sensor Direction Control 42
- Sensor Shift Direction 43
- Binning 44
- Resetting the Camera 44
- Camera Calibration 45
- Analog Processing 46
- Digital Processing 46
- Set Analog Gain 47
- Calibrate Camera Gain 47
- Calibration Returns: 48
- Update Analog Gain Reference 49
- Calibration Overview 49
- Correction Overview 50
- Digital Signal Processing 51
- Step 2: FPN Calibration 53
- PRNU Calibration Results 54
- Setting Digital Offset 54
- Subtracting Background 54
- Setting Digital System Gain 54
- Gate Dark Current Clear 55
- Auto Mode (srm 0) 55
- Setting the Readout Mode 57
- Appendix B: Sensitivity Mode 58
- Pixel DetailPixel Detail 59
- The GPIO Connector 60
- Configure GPIO Signal Levels 61
- Internal frame trigger 62
- Encoder 66
- Outputs 71
- Trigger Settings: GURU Mode 73
- Pulse Generator 76
- Pulse Period (ns) 77
- Pulse Frequency (Hz) 77
- Pulse Generator Timing 77
- Rescaler 78
- Counter 80
- Input Debouncing 81
- Timestamp Counter 82
- Clear Mode 83
- Clear Input 83
- Broadcast 83
- Set Value 83
- Current Value 83
- Delayer 84
- The PLC Control Block 85
- GPIO Output Labels 87
- Signal Routing Block 89
- How the Lookup Table Works 93
- Appendix D: EMC Declaration 94
- Examples: Setting the FVAL 99
- Revision History 102
Relacionado con productos y manuales para Cámaras De Seguridad Dalsa Spyder3
Cámaras De Seguridad Dalsa C1280 Manual de usuario
(133 paginas)
(133 paginas)
Cámaras De Seguridad Dalsa BOA Manual de usuario
(136 paginas)
(136 paginas)
Cámaras De Seguridad Dalsa BOA Manual de usuario
(12 paginas)
(12 paginas)
Cámaras De Seguridad Dalsa HM1400 XDR Manual de usuario
(157 paginas)
(157 paginas)
Cámaras De Seguridad Dalsa C1410 Manual de usuario
(131 paginas)
(131 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales