Dalsa Spyder3 Manual de usuario Pagina 88
- Pagina / 104
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
88 Spyder3 GigE Vision SG-14 Monochrome Cameras User’s Manual
03-032-20123-01 Teledyne DALSA
Signal
Label
Description
EXSYNC
Q4
EXSYNC
PRIN
Q5
PRIN
DIRECTION
Q6
Camera forward and reverse control.
CAM_CTRL (NOT
USED_
Q7
CC4 signal. Not used.
PULSE_TRIG1
Q8
Trigger for pulse generator 1. Used only when the pulse
generator is in triggered mode.
If available, can be used by one of the following modules:
Rescaler 0 input
Delayer 0 reference signal
Counter 0 clear event input
Timestamp counter set event input
Timestamp counter clear event input
PULSE_TRIG0
Q9
Trigger for pulse generator 0. Used only when the pulse
generator is in triggered mode.
If available, can be used by one of the following modules:
Rescaler 0 input
Delayer 0 reference signal
Counter 0 clear event input
Timestamp counter set event input
Timestamp counter clear event input
PULSE_TRIG3
Q10
Trigger for pulse generator 3. Used only when the pulse
generator is in triggered mode.
If available, can be used by one of the following modules:
Rescaler 0 input
Delayer 0 reference signal
Counter 0 clear event input
Timestamp counter set event input
Timestamp counter clear event input
PULSE_TRIG2
Q11
Trigger for pulse generator 2. Used only when the pulse
generator is in triggered mode.
If available, can be used by one of the following modules:
Rescaler 0 input
Delayer 0 reference signal
Counter 0 clear event input
Timestamp counter set event input
Timestamp counter clear event input
GPIO_FVAL
Q12
Output to the internal grabber to replace or mix with the
camera’s FVAL signal. Depending on the camera, the FVAL
signal can be replaced or combined with the signal of this
output.
GPIO_LVAL
Q13
Output to the internal grabber to replace or mix with the
camera’s LVAL signal. Depending on the cameral, the LVAL
signal can be replaced or combined with the signal of this
- Spyder3 SG-14 1
- Support 2
- Industry Standards 2
- Contents 3
- The Spyder3 SG-14 Cameras 6
- Certifications 10
- Responsivity 11
- Mechanicals 12
- Image Sensor 14
- Host System Requirements 15
- Network Adapter Requirements 15
- 5. Operate the Camera 16
- Install Network Card 17
- Configure Network Card 17
- Power Connector 20
- Status LED 21
- GPIO Isolation 22
- GPIO Configuration 22
- TTL Inputs and Outputs 23
- Power on the camera 24
- Connect to the camera 24
- Check LED Status 24
- Software Interface 24
- CamExpert Panes 26
- Review a Test Pattern Image 28
- Camera Operation 29
- User Setting 32
- Factory (Default) Settings 32
- External trigger 33
- Software trigger 33
- Valid Data From 34
- Diagramed 34
- Set the Exposure Mode 35
- Exposure Modes in Detail 36
- Line Rate 37
- Exposure Time 38
- Triggers 38
- Input / Output Control 39
- Image Size 41
- Pixel Format 42
- Sensitivity Mode 42
- Sensor Direction Control 42
- Sensor Shift Direction 43
- Binning 44
- Resetting the Camera 44
- Camera Calibration 45
- Analog Processing 46
- Digital Processing 46
- Set Analog Gain 47
- Calibrate Camera Gain 47
- Calibration Returns: 48
- Update Analog Gain Reference 49
- Calibration Overview 49
- Correction Overview 50
- Digital Signal Processing 51
- Step 2: FPN Calibration 53
- PRNU Calibration Results 54
- Setting Digital Offset 54
- Subtracting Background 54
- Setting Digital System Gain 54
- Gate Dark Current Clear 55
- Auto Mode (srm 0) 55
- Setting the Readout Mode 57
- Appendix B: Sensitivity Mode 58
- Pixel DetailPixel Detail 59
- The GPIO Connector 60
- Configure GPIO Signal Levels 61
- Internal frame trigger 62
- Encoder 66
- Outputs 71
- Trigger Settings: GURU Mode 73
- Pulse Generator 76
- Pulse Period (ns) 77
- Pulse Frequency (Hz) 77
- Pulse Generator Timing 77
- Rescaler 78
- Counter 80
- Input Debouncing 81
- Timestamp Counter 82
- Clear Mode 83
- Clear Input 83
- Broadcast 83
- Set Value 83
- Current Value 83
- Delayer 84
- The PLC Control Block 85
- GPIO Output Labels 87
- Signal Routing Block 89
- How the Lookup Table Works 93
- Appendix D: EMC Declaration 94
- Examples: Setting the FVAL 99
- Revision History 102
Relacionado con productos y manuales para Cámaras De Seguridad Dalsa Spyder3
Cámaras De Seguridad Dalsa C1280 Manual de usuario
(133 paginas)
(133 paginas)
Cámaras De Seguridad Dalsa BOA Manual de usuario
(136 paginas)
(136 paginas)
Cámaras De Seguridad Dalsa BOA Manual de usuario
(12 paginas)
(12 paginas)
Cámaras De Seguridad Dalsa HM1400 XDR Manual de usuario
(157 paginas)
(157 paginas)
Cámaras De Seguridad Dalsa C1410 Manual de usuario
(131 paginas)
(131 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.088 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales