Dalsa Spyder3 Manual de usuario Pagina 39
- Pagina / 104
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Spyder3 GigE Vision SG-14 Monochrome Cameras User’s Manual 39
Teledyne DALSA 03-032-20123-01
Start Mode
Frame Start Trigger Mode
Specifies whether the external fixed length frame trigger is
on or off. If the FrameTriggerActiveMode is on then it takes
precedence.To turn On, please DeviceScanType to Linescan
(Start Mode).
Frame Start Trigger Activation
Specifies what type of signal(i.e. high, or low) causes a
fixed length frame trigger when Frame Start Trigger Mode
is On.
Frame Start Delay
Enable the delayer.
GigE Vision Input Controls
Line Trigger Function Group
The Line Trigger Control section describes all features related to line acquisition using trigger(s). One
or many Trigger(s) can be used to control the start of an Acquisition, of a Line. It can also be used to
control the exposure duration at the beginning of a line.
Parameter
Description
Line Trigger Mode
The state of the line trigger. If the trigger is off, then the line
trigger is internally generated otherwise it is caused by an
external signal
Line Trigger Source
The external line that causes a line trigger.The line trigger is
from GPIO_PIN0. This feature is available only when Line
Trigger Mode in set to On.
Line Trigger Activation
Specifies what type of signal(i.e. high, or low) causes a line
trigger if Line Trigger Mode is On.
External Line Trigger Frequency
Reads the external line trigger frequency. NOTE: The
camera cannot detect frequency less than 5 Hz and will
display 1 if it cannot detect a signal. This featuer is
available when the Line Trigger Mode is se to ON and
Sensor Direction Control is set to External
Read External Line Frequency
Read the external line trigger frequency and updates the
ExternalLineTriggerFrequency register. This feature is
available when the Line Trigger Mode is set to On.
Input / Output Control
CamExpert groups the camera I / O Controls Parameters in either the Inputs group or the Outputs. These parameters
allow configuring the Spyder3 inputs and outputs for type of signal and signal polarity.
GigE Vision Input Controls
Inputs Group
This group contains the features that allow the configuration of the camera physical input lines (pins)
Parameter
Description
Line Selector
This feature selects which physical line (or pin) of the external
device connector to configure. When a Line is selected, all the
other Line features will be applied to its associated I/O control
block and will condition the resulting input or output signal.
Line0-- Line Trigger, Line1-- Frame Trigger, Line2 -- Direction.
- Spyder3 SG-14 1
- Support 2
- Industry Standards 2
- Contents 3
- The Spyder3 SG-14 Cameras 6
- Certifications 10
- Responsivity 11
- Mechanicals 12
- Image Sensor 14
- Host System Requirements 15
- Network Adapter Requirements 15
- 5. Operate the Camera 16
- Install Network Card 17
- Configure Network Card 17
- Power Connector 20
- Status LED 21
- GPIO Isolation 22
- GPIO Configuration 22
- TTL Inputs and Outputs 23
- Power on the camera 24
- Connect to the camera 24
- Check LED Status 24
- Software Interface 24
- CamExpert Panes 26
- Review a Test Pattern Image 28
- Camera Operation 29
- User Setting 32
- Factory (Default) Settings 32
- External trigger 33
- Software trigger 33
- Valid Data From 34
- Diagramed 34
- Set the Exposure Mode 35
- Exposure Modes in Detail 36
- Line Rate 37
- Exposure Time 38
- Triggers 38
- Input / Output Control 39
- Image Size 41
- Pixel Format 42
- Sensitivity Mode 42
- Sensor Direction Control 42
- Sensor Shift Direction 43
- Binning 44
- Resetting the Camera 44
- Camera Calibration 45
- Analog Processing 46
- Digital Processing 46
- Set Analog Gain 47
- Calibrate Camera Gain 47
- Calibration Returns: 48
- Update Analog Gain Reference 49
- Calibration Overview 49
- Correction Overview 50
- Digital Signal Processing 51
- Step 2: FPN Calibration 53
- PRNU Calibration Results 54
- Setting Digital Offset 54
- Subtracting Background 54
- Setting Digital System Gain 54
- Gate Dark Current Clear 55
- Auto Mode (srm 0) 55
- Setting the Readout Mode 57
- Appendix B: Sensitivity Mode 58
- Pixel DetailPixel Detail 59
- The GPIO Connector 60
- Configure GPIO Signal Levels 61
- Internal frame trigger 62
- Encoder 66
- Outputs 71
- Trigger Settings: GURU Mode 73
- Pulse Generator 76
- Pulse Period (ns) 77
- Pulse Frequency (Hz) 77
- Pulse Generator Timing 77
- Rescaler 78
- Counter 80
- Input Debouncing 81
- Timestamp Counter 82
- Clear Mode 83
- Clear Input 83
- Broadcast 83
- Set Value 83
- Current Value 83
- Delayer 84
- The PLC Control Block 85
- GPIO Output Labels 87
- Signal Routing Block 89
- How the Lookup Table Works 93
- Appendix D: EMC Declaration 94
- Examples: Setting the FVAL 99
- Revision History 102
Relacionado con productos y manuales para Cámaras De Seguridad Dalsa Spyder3
Cámaras De Seguridad Dalsa C1280 Manual de usuario
(133 paginas)
(133 paginas)
Cámaras De Seguridad Dalsa BOA Manual de usuario
(136 paginas)
(136 paginas)
Cámaras De Seguridad Dalsa BOA Manual de usuario
(12 paginas)
(12 paginas)
Cámaras De Seguridad Dalsa HM1400 XDR Manual de usuario
(157 paginas)
(157 paginas)
Cámaras De Seguridad Dalsa C1410 Manual de usuario
(131 paginas)
(131 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales